Eagle Eye VMS Camera Direct Complete Setup and User Guide

Eagle Eye VMS Camera Direct Complete Setup and User Guide

Eagle Eye VMS Camera Direct Complete Setup and User Guide

This guide describes how to add Camera Direct cameras to the Eagle Eye Cloud VMS.


With Eagle Eye VMS Camera Direct, you can easily integrate your cameras with the Eagle Eye Cloud VMS without the need for a Bridge or CMVR. Connect your camera to the internet and add it to the Eagle Eye Cloud VMS using its MAC address. Once added, your cameras are immediately ready for viewing within the Cloud VMS.

Supported Cameras

The following cameras are currently supported with Eagle Eye Camera Direct Complete: 





Eagle Eye Camera DB10 Outdoor Bullet 4 MP (MegaPixel), H265, IR, IP66, 2.8mm, WDR, PoE


Eagle Eye Camera DB11 Outdoor Mini Bullet 4 MP, H265, IR, IP66, 2.7-13.5 Lens, WDR, PoE


Eagle Eye Camera DM08 Outdoor Mini Dome 4 MP, H265, IR, IP66, 3.6mm Lens, Microphone, PoE


Eagle Eye Camera DD07 Outdoor Vandal Dome 4 MP, H265, IR, IP67, IK10, DarkSight, 2.8mm Lens, PoE



Eagle Eye Camera DD08 Outdoor Vandal Dome 4 MP, H265, IR, IP66, IK10, DarkSight, 2.7mm-13.5m Moto Lens, PoE 

Eagle Eye Camera DD09 Outdoor Vandal Dome 4 MP, No Pigtail, H265, IR, IP67, IK10, 2.7mm-13.5m Moto Lens, PoE


Eagle Eye Camera DT01 Outdoor Turret 4 MP, H265, IR, IP66, 2.8mm Lens, PoE

Adding a Camera Direct Camera to the Eagle Eye Cloud VMS


In order to set up your Eagle Eye Camera Direct, you need the following: 
  1. An Eagle Eye Cloud VMS account. 
  2. A camera model that is supported by Camera Direct.
    1. Note: Make sure the camera is in factory default settings, and runs the latest firmware for its model. 
  3. The MAC address of the Camera Direct camera.


Make sure the camera is turned on and is connected to the internet. 
  1. Go to the Eagle Eye Cloud VMS and log in with your credentials. 
  2. Go to Dashboard.
  3. Click the  icon, and choose Add Camera Direct from the drop-down list.
  4. In the Add Camera Direct dialog, name the camera and enter its MAC address

  1. The Camera Direct Camera is added to your Eagle Eye Cloud VMS account.

It will initially be listed as offline on the dashboard, but after a maximum of two minutes should be marked with a green check mark indicating an online status.
Using the Live View and History Browser with Camera Direct cameras in the Eagle Eye Cloud VMS works the same way as it does with any other cameras. If you need assistance refer to our knowledge base article here.

Upcoming Features

At present, Camera Direct cameras do not support the following features: 
  1. VPN to cameras 
  2. Analytics (other than motion) 
  3. Camera I/O support 
  4. 2-Way Audio support
  5. License Plate Recognition (LPR) support

    • Related Articles

    • DS200: Display Station Setup Guide

      DS200 Setup Guide Quick notes: If you do not have the login information for the device please boot into safety mode to reset the password. To boot into this hold both shifts and reboot the unit. This will prompt you to set a password for the device ...
    • Hikvision Configuration Guide

      This guide illustrates how to configure Hikvision cameras for integration with the Eagle Eye Security Camera System. It may be required to use Windows with Microsoft's Edge browser in Internet Explorer mode or to use Mac OS X with Safari to complete ...
    • Camera Direct FAQ

      Camera Direct Complete FAQ Is Camera Direct a new Cloud-based VMS? No, Camera Direct Complete is a direct-to-cloud solution that utilizes the Eagle Eye Cloud VMS and eliminates the need for a Bridge/CMVR. This means that there is essentially no ...
    • Eagle Eye User Permissions

      Eagle Eye User Permissions This article explains the permission settings available for users of Eagle Eye's Cloud VMS.  All features mentioned in this article may not be visible to all users and are based upon the agreement with the Eagle Eye ...
    • Axis Camera Configuration Guide

      Axis Camera Configuration Guide Most Axis camera’s default settings are compatible with our system. The main functionality that needs to be set up for the camera to stream is ONVIF. Please follow these steps to enable the functionality. 1. Login to ...