How to Power Cycle an Eagle Eye Bridge/CMVR

Power cycling an Eagle Eye Bridge/CMVR

This article details how to power cycle an Eagle Eye Bridge/CMVR.  Eagle Eye offers several different models of Eagle Eye Bridges and CMVRs.  Each model has a power button that can be used to power down the device, but start-up times may differ based on the size and model of the Eagle Eye Bridge/CMVR.  

If you are troubleshooting an  Eagle Eye CMVR 820, please do not power cycle without contacting Support first.  

How to power cycle Eagle Eye Bridges 304, 305: 

      1. Press the power button once and the unit will power down. 

      2.  Wait for one full minute.

      3.  Press the power button again to power the unit back up.  

If the unit does not power down or will not power back up, please contact Support. 

How to power cycle Eagle Eye Bridges 301, 401, 501, 303, 305, 403. 410, 510:

1.  Press and hold the power button for 5 seconds or until the lights turn off and the device powers down. 

The link lights may stay on even though the unit is powered down. 

      2.  Wait for one full minute.

      3.  Press the power button again to power the unit back up.  

If the unit does not power down or will not power back up, please contact Support. 

How to Power Cycle Eagle Eye CMVRs 224, 324, 324, 325: 

      1.  Press the power button once and the unit will power down.

      2.  Wait one full minute.

      3.  Press the power button again to power the unit back up. 

 If the unit does not power down or will not power back up, please contact Support.

How to Power Cycle Eagle Eye CMVRs 320, 420, 330, 430:

      1.  Hold the power button for 5 seconds or until the unit powers down. If the unit does not power down or will not power back up, please contact Support.

The link lights may stay on even though the unit is powered down. 

     

      2.  Wait for one full minute.

      3.  Press the power button again to power the unit back up. 

If the unit does not power down or will not power back up, please contact Support.

How to Power Cycle Eagle Eye CMVRs 520, 620:

      1.  Hold the power button for up to 10 seconds or until the unit powers down.

    The link lights may stay on even though the unit is powered down. 

      2.  Wait 5 minutes.

      3.  Press the button to power the unit back on. 

If the unit does not power down or will not power back up, please contact Support.

If you have any questions or concerns, please contact us. 

US: +1-512-473-0501 

EU: 31 (0) 20 26 10 460

ASIA PACIFIC: 81-3-686-5527

• Related Articles

• Offline Bridge Troubleshooting Guide

  Behind a firewall? Before continuing please check here and ensure it's configured for our device. You will need to contact Eagle Eye Networks support for your bridge or CMVR username and password. This article is meant for technician or installers. ...

• Performing a Bridge Swap

  Bridge Swap A Bridge Swap will replace an offline bridge with a new online bridge.  The attached cameras will transfer to the new bridge on the dashboard.  Please ensure the new bridge is set up on-site exactly like the original bridge. IMPORTANT!!  ...

• Adjusting Network settings on an Eagle Eye Bridge/CMVR -- Setting a Static IP

  Adjusting Network Settings on Eagle Eye Networks Bridge/CMVR Devices By default, all of our devices are set up for DHCP on the WAN and the CamLAN. In order to reconfigure these settings we recommend you connect a keyboard and monitor. The steps below ...

• Connecting to a Bridge/CMVR

  Connecting to a Bridge/CMVR There are 3 ways to connect directly to the bridge/CMVR: Note: if a bridge fails to reach the login screen a HMDI monitor and USB keyboard will be required.  A usb keyboard and a monitor with an hdmi cable A usb cable and ...

• Bridge Configurator Menu Guide

  Bridge Configurator Menu Guide The Bridge Configurator Menu is available on CMVRs This guide describes what options exist in the Bridge Configurator Menu in order to connect to a bridge. For detailed instructions for troubleshooting offline bridges, ...