ANV108 Low Bandwidth in Camera Direct

ANV108 Low Bandwidth in Camera Direct

This Application Note is intended for Brivo Eagle Eye Camera Direct end users who are concerned about high data and bandwidth usage.

Application Note: Video – ANV108 

Low Bandwidth in Brivo Eagle Eye Camera Direct

2026-09-09   Revision 2.0

Target Audience


This Application Note is intended for Brivo Eagle Eye Camera Direct end users who are concerned about high data and bandwidth usage. It also explains how to remove the restriction on the number of Camera Direct cameras per site. 


Introduction


The current implementation of Camera Direct cameras always streams high-resolution H.264 video to the cloud, resulting in high data consumption and being especially ill-suited for a camera operating over a mobile network. This feature provides a low-bandwidth solution for Camera Direct cameras to reduce data consumption. This approach relies on switching to two video streams and requires the use of an SD card for local storage.


The low-bandwidth solution is achieved by the camera switching to two streams:

  • A low-resolution H.264 stream (640×480, 4 fps) streams continuously for preview.

  • A high-resolution H.264 stream is requested and streamed only in response to edge events.

To switch to a low-bandwidth solution, you must have a working Edge storage SD card installed in the camera. When the high-resolution stream is requested after an event, any gap of a few seconds is filled, and pre-recording (3 seconds) is provided by syncing data from the SD card.

Make sure an SD Card is present in the Camera for the low-bandwidth mode to work


Enabling the low-bandwidth mode

The camera always defaults to low-bandwidth mode if it detects an SD card and Record When is set to Event.


Events that can be used 

Once you select Event in Step 1, you can now select any of the Events in the Analytics tab. 

  1. Cloud Motion Detection 

  1. Camera Events

You can also use any Camera Analytics for cameras with integrated on-camera analytics, e.g., Pro series, Axis, etc. Simply set up Analytics on the camera and enable it in Camera → Settings → Analytics. Please refer to ANV093-Using Edge Analytics with Pro Series Cameras or ANV091-Enabling Axis Object Analytics (AOA) Events in Brivo Eagle Eye Video for more details.  



FAQ

What is the “Camera Direct – Low Bandwidth Support” feature?

It’s a smart new recording option for Eagle Eye Camera Direct that significantly reduces the amount of internet data your cameras use. It works by continuously streaming a low-quality preview, recording, and uploading high-quality video only when important events occur.

Why would I want to use this feature?

This mode is perfect if your camera setup involves:

  • Mobile internet connections (like 4G/5G)

  • Remote locations: where internet bandwidth is limited or unreliable.

  • Situations where data usage is a concern, especially if you have data caps or want to save on cellular costs.

You still get a usable live preview, and all your important events are captured in high quality, without the high cost of continuous high-resolution streaming.

How does it reduce my internet data usage?

It uses two ways of capturing video from your camera:

  • Continuous low-quality video: This smaller video feed runs continuously for live viewing and quick snapshots (thumbnails). It uses very little data.

  • High-quality video: This activates and streams only when an important event occurs, like motion detection.

Using high-quality video only when absolutely needed drastically reduces your overall data consumption compared to streaming high-quality video 24/7.

How much bandwidth does a Camera Direct camera use in low-bandwidth mode?

In low-bandwidth mode, a Camera Direct camera uploads two things: a continuous low-resolution preview stream, and short bursts of high-resolution video when an event is triggered.

The continuous preview stream is 640×480 at 4 fps and typically uses 80–150 kbps. This runs 24/7 and is the floor of your bandwidth usage.

The high-resolution stream only uploads during and shortly after an event. For a typical 2MP camera at 15 fps, this is 750 to 1250 kbps while it is active. Because the pre-roll and gap-fill footage is synced from the SD card at the same time as the live high-resolution stream, the burst can briefly run above that figure.

For sizing an internet connection, plan for the peak rather than the average. A single 2MP camera needs roughly 1.25 Mbps of upload headroom so an event burst doesn't saturate the link. Multiply this by the number of Camera Direct cameras at the site if events are likely to overlap.

How much monthly data will low-bandwidth mode use on a cellular plan?

Total data depends almost entirely on how many events the camera triggers, since the preview stream is a fixed cost. As a rule of thumb, the preview stream alone uses about 1.1 GB per day, or roughly 32 GB per month, and every minute of high-resolution event video adds about 7.5 MB.

Three worked examples, all assuming a 2MP camera at 15 fps:

Site type

Event activity

High-res video per day

Total per day

Total per 30 days

Quiet remote site (perimeter gate, pump station)

20 events, 30 sec each = 10 min

75 MB

~1.2 GB

~35 GB

Moderate activity (loading dock, small car park)

60 events, 45 sec each = 45 min

340 MB

~1.4 GB

~43 GB

Busy site (retail entrance, main lobby)

200 events, 30 sec each = 100 min

750 MB

~1.9 GB

~55 GB


Tuning your event configuration is your biggest lever. A camera pointed at a busy road with cloud motion detection enabled will trigger far more often than one using person or vehicle analytics on the same scene, and the difference shows up directly on your data bill.

How do I calculate the bandwidth for my specific camera and site?

The figures above are typical cases. Actual usage varies with resolution, frame rate, scene complexity, lighting, and how much motion is happening in front of the camera. A 4MP camera in a scene with moving foliage will use considerably more than a 2MP camera pointed at a quiet doorway.

To estimate your own case, take the preview stream as a fixed 32 GB per month, then add your expected event minutes per day multiplied by the per-minute rate for your camera's resolution and frame rate.

We are also updating Product Wizard to recommend the bandwidth needed for a Camera Direct camera, which will handle this calculation for you.

The above answers are for a typical case, but I want to know the bandwidth usage for my case. How can I find that? 

We are updating Product Wizard so it recommends the bandwidth needed for a Camera Direct camera. 

Will I still get high-quality video of important events?

Absolutely! When an event is detected, the system immediately:

  1. Starts recording the high-quality video.

  2. Retrieves a few seconds of "pre-roll" video (footage from just before the event) directly from your camera's SD card.

  3. Combines these seamlessly into one continuous, high-quality clip.

This ensures you see everything that happened just before and during the event in full detail.

What is “pre-roll” and why is it important?

"Pre-roll" is the video your camera captures a few seconds before the event. Since the high-quality video isn't always streaming, there might be a tiny delay while it starts up. Pre-roll fills this gap, so you don't miss the beginning of any crucial event.

What types of events can trigger a high-quality recording?

All events, including Motion, person, vehicle, etc., can trigger high-quality recordings. 

What are the different "Record when" options?

You'll typically have options like:

  • Always: For continuous recording.

  • Event: Recording triggered by events detected either by the camera (like the Axis or Eagle Eye Pro series) or by cloud motion Events. 

Do I need an SD card in the camera for this to work?

Yes, a working SD card in your camera is essential for low-bandwidth mode. The SD card continuously records on the camera, allowing us to retrieve that crucial "pre-roll" video and cover any gaps when the high-quality stream starts. Without a healthy SD card, this feature won't work.

How quickly will event videos be available to view?

Our goal is for your "pre-roll" footage to be available alongside the recording of the incident in approximately 15 to 20 seconds once the activity has occurred.

Is this feature included with my current plan, or do I need to upgrade?

This feature is designed to be available across all product editions without requiring new permissions or special branding changes. Please check with your account representative for specific availability details.