Application Note: Video - ANV099
Device and Camera Status Definitions and Processing
2025-04-21 Revision 1.0
This Application Note is intended for resellers and end-user administrators of Brivo Eagle Eye Video. It provides a high-level overview of the camera status definitions and flow, providing users a better understanding of VMS camera status and notifications.
Users need to know if their cameras are online or offline. This Application Note covers the most common camera status values, how those values are determined, and how they are communicated to you.
This application note clearly defines the different status levels observed in Brivo Eagle Eye Video Dashboard. Once the status levels are clarified, the application note outlines how each status level is determined and communicated.
When users access the Dashboard, they see a display similar to that shown in Figures 1 and 2.
Figure 1: Dashboard - Classic Interface
Figure 2: Dashboard - Enhanced Web Interface
The Device Status icons indicate the following status levels.
Device Status
– ONLINE - The camera is online. Everything is working as expected.
– OFFLINE - The camera is offline. The bridge is communicating with the VMS. However, the Bridge/CMVR cannot determine the status of the camera. This can be due to the camera being physically powered off, or there could be a physical or network issue between the camera and the Bridge/CMVR.
– OFF - The camera is turned off in Camera Settings. The camera is physically powered on but is not transmitting video to the VMS because it is turned off in Camera Settings. To resume video transmission, go to Camera Settings → Camera, then check the On box.
– INTERNET OFFLINE - The camera’s internet is offline. The Bridge/CMVR that the camera is connected to is not communicating with the VMS. There are a variety of network issues that can cause this, such as the internet is down at that site or perhaps a firewall is misconfigured.
– NEW - The camera is ready to be connected to the VMS.
– FAILING RESPONSE - Communication with the camera is failing, possibly due to a login credentials issue.
There are several key components involved in determining the status of a device or camera. This section describes the role of each component and its standard processing under normal conditions. The next section will cover unusual conditions and how they affect the determination of Status.
Components
User Interface (UI) - The UI communicates directly with the VMS processes to receive and display device and camera statuses. All status values are provided to the UI by VMS processes.
Bridge/CMVR - The Bridge/CMVR units communicate with both the cameras and the VMS Processes to determine status values and post the appropriate values.
VMS Processes - The VMS Processes synchronize status values and post them for the UI to consume.
The process for determining the status value works as described below for each status:
ONLINE: This status value applies to cameras and devices. A camera is considered online when it responds to status checks from the Bridge/CMVR (or the cloud for Camera Direct cameras) and provides media data as expected. Both the Bridge/CMVR and the VMS Processes confirm that the camera is sending the expected responses and data. For other device status values, the VMS Processes confirm connectivity and that the devices are responding with appropriate data loads.
OFFLINE - This status applies to cameras only. The Bridge/CMVR (or the Cloud for Camera Direct cameras) first confirms that it can connect to the camera. Further, the Bridge/CMVR inspects multiple levels of functionality within the appropriate protocol (e.g., RTSP, ONVIF) to determine if the expected data is flowing properly. If any level of data is not flowing properly, the camera is considered OFFLINE.
OFF - This status value is for cameras only. The OFF status is user-initiated through the UI. The camera is turned off in the UI in the Camera Settings. The camera is still powered on. The camera is still reachable and communicating properly with the Bridge/CMVR. However, the camera has paused sending video at the end user’s request.
INTERNET OFFLINE - This status applies to cameras and devices. The VMS Processes report INTERNET OFFLINE when the Bridge/CMVR and VMS Processes cannot communicate. Additionally, if the Bridge/CMVR can communicate with the VMS Processes, but the media data flow between the two is not functioning properly (e.g., uploaded video cannot be stored on the VMS storage system), the VMS Processes will assign the status value INTERNET OFFLINE.
NEW - This status value is for cameras only. When a Bridge/CMVR detects a camera on the network that has not yet been added to a Bridge/CMVR, the camera is assigned the NEW Status value. Once an administrator adds the camera to a Bridge/CMVR, the camera will be assigned the appropriate status value: ONLINE.
FAILING RESPONSE - This status is for cameras only. This status value indicates that the camera credentials are incorrect or improperly stored in the system. Once the correct credentials are stored, it may take a few minutes for the bridge to communicate the updated password to the camera, and the status is set to an appropriate value: ONLINE.
These status values are checked at regular intervals, within seconds of each previous check. However, for some status values, such as OFFLINE, checks and automated corrective actions may delay the status change by up to a few minutes.
As mentioned above, status checks are performed at very short intervals. Most status values are determined and assigned within seconds. Some status values require slightly longer intervals to be assigned due to factors such as protocol timeouts and automated corrective action attempts.
Status values that are determined and assigned rapidly are:
ONLINE
OFF
NEW
FAILING RESPONSE
Status values that could require slightly longer intervals are:
OFFLINE - If the connection between a Bridge/CMVR and a camera is completely unavailable, the OFFLINE Status level will be determined and assigned immediately. However, if the camera is reachable, determining whether it should be assigned OFFLINE depends on the camera's responses to the appropriate protocol communication checks. Is the camera sending the appropriate data (e.g., video, audio, etc.)? Is the data flowing with the expected bit rate? Other appropriate values are checked, and the Bridge/CMVR determines the status value based on the results of those checks. Additionally, the Bridge/CMVR will attempt automated corrective actions for some of the protocols it checks. These actions can add a few seconds to tens of seconds to the Status value determination process.
INTERNET OFFLINE - If the connection between a Bridge/CMVR and the VMS Processes is completely unavailable, the INTERNET OFFLINE Status level will be determined and assigned immediately. However, if the Bridge/CMVR and the VMS Processes can communicate, determining whether a unit should be assigned INTERNET OFFLINE depends on checks to confirm that the camera’s data can be successfully written to the VMS storage system. The status of these data writes is generally determined within seconds, but may be delayed by tens of seconds if automated corrective actions are attempted to alleviate data storage issues.
So, camera and device status values are normally assigned and recorded within seconds. In cases where the OFFLINE or INTERNET OFFLINE status values require protocol timeouts or automated corrective actions, the Status values may take 2–4 minutes to be assigned and recorded.
Brivo Eagle Eye Video allows you to set camera status notification delivery intervals. By default, Status value notifications are sent after 900 seconds (15 minutes). This value is set to limit over-notification caused by temporary connectivity issues that may occur during a status check. If a status persists for the duration of the notification interval, then a notification will be sent. An additional notification will be sent when the camera's status changes.
The status notification delivery interval can be modified, but you should consider the potential for an influx of notifications if you shorten it significantly. There are a variety of conditions that can cause connectivity or data flow interruptions. Brivo Eagle Eye Video is engineered to recover gracefully from any such interruption. So, keeping the notification interval at a reasonable frequency, such as 900 seconds, increases the likelihood that a status-value notification indicates a specific issue rather than a temporary interruption in normal communication.
When considering when to expect a status value notification, remember to include the time required to determine the status value, in addition to the configured notification interval.
Brivo Eagle Eye Video provides robust status-value monitoring. The Bridge/CMVR and the VMS Processes check multiple factors to determine the status value of cameras and devices. They will also attempt automated corrective actions to address any issues. When determining when to expect status value notifications, consider the time required to determine the Status value, plus the status notification interval settings for your environment.