Application Note: Video - ANV083
Installing and Configuring the Siren on Brivo Eagle Eye Cabinet Systems
2025-07-23 Revision 1.0
This Application Note provides information about installing and configuring the siren for the Brivo Eagle Eye DX01, DT03, DB13, and DB14 cameras in both the Classic and Enhanced Web Interfaces of Brivo Eagle Eye Video. This app note is intended for technicians and other installers of the Brivo Eagle Eye Direct and Anywhere Cabinet Systems.
Follow the steps in this section to obtain the camera’s IP address.
Connect the laptop to one of the Ethernet ports on the in-hand router.
Open a web browser and go to http://192.168.2.1
The password will be the serial number of the router, followed by an exclamation mark—e.g., RF3022319236617!.
Once logged in, click the Status tab, then Device List.
You should see two devices in the list: one is the camera, and the other is the laptop you used to connect to the router.
The IP address is located next to the MAC address in the Device List. Once you have the IP address, you can move to the next section.
Use the instructions in this section to log into the camera where you will connect the IP speakers. The camera must be physically connected to the router using an Ethernet cable.
Once you know the IP address, open a tab in your web browser and navigate to that IP address. See the figure below for an example of a login screen.
Log in to the system. The username is 'admin', and the password is the one provided on the printout for the camera.
Once you are logged in, the UI may appear slightly different depending on the camera you are using.
Use the instructions in this section to configure DX01, DT03, or DB13 cameras for the speaker.
Once logged in, click the Configuration tab, then Alarm on the left menu.
Adjust the alarm duration to your preference. The default setting of 0 milliseconds results in a continuous alarm, which can lead to battery drain. To set the alarm for 1 minute, use 60000 ms; for 2 minutes, use 120000 ms, and so on.
Click Apply to save the settings. Once this is complete, proceed to the section on Configuring the Camera in Brivo Eagle Eye Video: Enhanced Web Interface or Configuring the Camera in Brivo Eagle Eye Video: Classic Interface.
Use the instructions in this section to configure DB14 cameras for the speaker.
Once logged in, click the Settings tab, then Event on the left, then the Alarm Out tab.
Adjust the alarm duration to your preference. The default setting of 0 milliseconds results in a continuous alarm, which can lead to battery drain. To set the alarm for 1 minute, use 60000 ms; for 2 minutes, use 120000 ms, and so on.
Click Apply to save the settings. Once this is complete, proceed to the section on Configuring the Camera in Brivo Eagle Eye Video: Enhanced Web Interface or Configuring the Camera in Brivo Eagle Eye Video: Classic Interface.
Use the instructions in this section to configure the siren in the Enhanced Web Interface of Brivo Eagle Eye Video.
Go to your dashboard, then navigate to the Direct to Cloud Cameras section.
Find the camera you want to adjust, click the three dots icon on the right, then select Settings.
Navigate to the IO tab, then select Output.
Toggle on the Turn on Output button as well as the Icon on Screen button.
Choose the button type from the drop-down list, then click Save.
Navigate to the Dashboard and open the live view.
In the bottom right of the live view, click the Input and Output button, which is represented by the arrows.
When you click the button, it expands to display the icon you previously selected.
You can also access the siren from Layouts.
Click the icon to manually trigger the siren sound and lights. The icon will appear red, indicating that it is active.
Whatever number in milliseconds you set for the Alarm Time is how long the siren will sound. It will automatically shut off after that time. If you leave it at the default of 0 milliseconds, the siren will continue to go off until the battery dies or you click the icon again to turn it off.
Even if the siren is configured with a timeout in the camera settings, the icon will remain red after the set time. You must manually deactivate the icon to re-trigger the siren.
There is a possibility of a slight delay from the time you trigger it to when the siren activates due to network conditions.
Use the instructions in this section to configure the siren in the Classic Interface of Brivo Eagle Eye Video.
Go to the Dashboard, then navigate to the Direct-to-Cloud Cameras section.
Find the camera you want to adjust, then click the gear icon on the right. A screen similar to the one below opens.
Navigate to the IO tab, then to the Output tab.
Check the box to Enable Camera Output 1, then click the down arrow to the right of the test button.
Change the settings to match the ones below and select your Icon on Screen using the drop-down menu.
Once options are chosen, click Save Changes.
Go back to the Dashboard.
Click the preview, and you will see your icon there.
Alternatively, you can click to view the larger live view and see the button there as well.
It can also be accessed from Layouts.
Click the icon to manually trigger the siren sound and lights. The icon will turn red, showing it is active.
Whatever number in milliseconds you set for the “Alarm Time” is how long the IP siren will sound. It will automatically shut off after that time. If you leave it at the default of 0 milliseconds, the siren will continue to go off until the battery dies or you click the icon again to turn it off.
Even if the siren is configured with a timeout in the camera settings, the icon will remain red after the set time. You must manually deactivate the icon to re-trigger the siren.
There is a possibility of a slight delay from the time you trigger it to when the siren activates due to network conditions.
This application note has provided comprehensive instructions for installing and configuring the siren with the Eagle Eye DX01, DT03, DB13, and DB14 cameras when used with Eagle Eye Direct or Anywhere Cabinet Systems. By following the detailed steps for obtaining IP addresses, logging into cameras, configuring camera settings, and integrating with both the Classic and Enhanced Brivo Eagle Eye Video interfaces, technicians can successfully deploy the siren to enhance security and communication. Proper configuration of alarm durations and understanding the behavior of the alarm icons in the VMS are crucial for optimal performance