Application Note: Video - ANV075
Installing Two Solar Panels on the Brivo Eagle Eye Anywhere Cabinet Systems
2026-10-19 Revision 3.0
This application note provides a step-by-step guide for professional installers on installing two solar panels for use with the Brivo Eagle Eye Anywhere Cabinet Systems (SS212 and SS213). This installation optimizes performance by connecting both panels in parallel and is designed specifically for pole-mounted setups. This document is for installers knowledgeable about electrical installation.
Before installing two solar panels on the Brivo Eagle Eye Anywhere Cabinet System, review the following safety precautions and gather the necessary materials.
Ensure all electrical work complies with local codes and regulations.
Wear personal protective equipment (PPE).
De-energize any connected power sources before installation.
Use insulated tools to prevent accidental electrical shocks.
Two Brivo Eagle Eye 120W (EN-SZ004), or 200W (EN-SZ007) solar panels
Brivo Eagle Eye SS212 (EN-SS212) or SS213 (EN-SS213) Anywhere Cabinets
Solar panel mounting brackets (Supplied)
Pole or light pole (with sufficient height for unobstructed sunlight)
EN-SZ002 Y-cable with MC4 connectors
Tools: drill, screwdriver, wire cutters/strippers, wrench, multimeter
Installation has three steps: planning, mounting, and connecting. Planning is the most important and involves multiple considerations. Mounting may be difficult simply because of the awkwardness of working at the height and handling large panels. With good planning and patience, the installation should be straightforward. Connecting is easy: plug in the MC4 connectors to power the cabinet.
Material and Strength: Ensure the pole is structurally sound and can support the weight of the solar panels, mounting hardware, and the cabinet. Consider wind load and local weather conditions.
Location: Shadows on any part of the panels will significantly reduce available power. Ensure the installation site has full sun exposure, ideally at least 8 hours per day. Ensure there are no obstructions (trees, buildings, etc.) that will cast shadows on the panels.
Height Considerations: The pole should be tall enough to place both panels one above the other. Because of the limitations of the one-pole and the solar panel mounting brackets, you must install one panel directly above the other. Ensure sufficient distance between the two panels so the upper panel does not cast a shadow on the lower panel, even in summer when the sun is highest in the sky.
Figure 1: Lower 48 U.S. States Latitude Map
Refer to Figure 1 and Table 1 to determine the distance between the two solar panels as a function of latitude and panel type.
Table 1: Separation distance for two solar panels depending on latitude and panel type
Figure 2: Correct Positioning of Solar Panels on a Pole. The distance between panels varies by Latitude.
Orientation: Solar panels should face due (true) south to capture the most sunlight. Make sure the solar panels face true South, not magnetic South. In some locations, the difference between true South and magnetic South could mean losing more than 5% of power. Both panels must be aligned and face the true South. Note: Most smartphones can find true South. Square Poles: Installations on square poles can make it difficult to face due South. We offer this corner bracket to address this situation: EN-CACM-002. It lets you mount the panels on the corner of a square pole.
Panel Tilt: The tilt angle is important for capturing as much of the sun’s energy as possible, but it matters less than orientation toward the South, and achieving any set angle within +/- 3-4 degrees is difficult with this installation. The angles listed in the chart below are optimized for year-round performance, with an emphasis on Winter. Use the map above to find your latitude, then read the chart to find the appropriate tilt angle. Again, tilt both panels to the same degree.
Tilt Angle
Mount the Solar Panels
Note: The panels are large and awkward to position with the brackets attached. Do not attempt to mount the panel without assistance. You need two hands to thread the metal strap into the worm gear and tighten it.
After determining the proper tilt angle for the panels, set that angle on the brackets that hold the solar panels. Measure the distance between the top and bottom. Mark the pole at the appropriate distance to guide you as you install the mounting brackets and straps.
Thread the metal straps through the solar panel brackets. Then wrap the straps around the pole, into the worm gear, and tighten them. A drill isn't required, but it's highly recommended to tighten the strap using the worm gear.
Secure both panels to the pole. Position them at the proper angle for your geographical location. Ensure they are both at the same angle.
Ensure the panels are securely fastened to withstand wind and weather conditions.
Configure the Panels in Parallel
Connect the two solar panels electrically and physically in parallel to ensure optimal performance. Point both panels at the same angle toward the sky. Tilting one at a different angle to get more sun at a different time of day or year will cause the pair to generate power at the level of the lower-performing panel.
Connect the two solar panels in parallel to maintain the voltage while increasing the current. Do this by connecting the positive terminal of the first panel to the positive terminal of the second panel, and the negative terminals likewise. Note: Use care when tracing the connections to ensure the proper polarity. When using solar cables with MC4 connectors, the keyed connectors help prevent mistakes but may confuse users because the colors change.
Our Y-connectors (EN-SZ002) have keyed MC4 connectors for ease and weather resistance. If you need longer cables for a location not adjacent to the cabinet, we recommend solar extension cables with MC4 connectors, which are readily available.
Connect the Panels to the Brivo Eagle Eye SS212 or SS213 Cabinet
Refer to the Quick Start Guide for your cabinet model.
Test the Installation
Double-check all connections and ensure they are secure.
Verify that the solar panels remain unobstructed by any shadows throughout the day.
Clean the solar panels to remove any dirt or debris that may hinder their performance.
Clean Regularly: Clean the solar panels periodically to remove any dirt, dust, or debris that may accumulate and block sunlight. This can significantly improve efficiency.
Inspect Connections: Regularly check connections.
Permits and Zoning: Check with local authorities regarding any necessary permits or zoning regulations for installing solar panels on public or private property.
Safety Codes: Ensure that all installations comply with the National Electrical Code (NEC) and other relevant electrical safety standards.
If the system is not producing the expected power, check for shading, dirty panels, loose connections, or faulty components.
Monitor performance over time and look for patterns related to environmental conditions, such as seasonal changes in sunlight exposure.
If the system is not functioning, inspect all wiring and connections for damage or disconnection.
Following the instructions in this application note will ensure a successful installation of two solar panels for the Brivo Eagle Eye SS212 or SS213 Anywhere Cabinet Systems. This setup provides reliable power, improving the cabinet's performance and longevity in outdoor applications. Always refer to the product manuals for specific details and safety guidelines.
For more information on operation or troubleshooting tips, please contact your reseller or contact support: support.brivo.com