ANV041 Brivo Eagle Eye Video LPR integration with Moxa

ANV041 Brivo Eagle Eye Video LPR integration with Moxa

Application Note: Video – AN041 

Brivo Eagle Eye LPR Integration with Moxa for Vehicle Access Control


2024-09-05   Revision 2.0


Target Audience


This Application Note is intended for Brivo Eagle Eye Video administrators who would like to integrate Brivo Eagle Eye LPR (License Plate Recognition) with the Moxa I/O unit to open gates for vehicle access control through License Plate Local ID. A basic working knowledge of Brivo Eagle Eye Video and Brivo Eagle Eye LPR is recommended before making any changes to configuration settings. 


If you need additional details on the camera installation aspect of LPR and VSP, please read AN033 Camera Installation Considerations for LPR/ANPR and AN034 Configuring LPR in the Eagle Eye VMS.


Introduction


Brivo Eagle Eye Video allows the use of License Plate Recognition (LPR) analytics to read the license plates of vehicles. The license plate recognition from Brivo can be used for applications such as access control to open gates. 


Brivo Eagle Eye LPR with Local ID enables verification of license plates using a preconfigured allow list and/or deny list, and triggers an I/O event upon detection of an allowed or denied vehicle. The LPR service running on the Bridge is integrated with the MOXA ioLogik E1214 I/O module for access-control applications (e.g., to trigger a gate). This document describes how to configure this setup.


Architecture


The part numbers needed for this setup are:

Part Number

Description

Remark 

EN-ANA-022-X Or ENi-ANA-022-X

Brivo Eagle Eye Analytic License Plate Recognition w/Local ID

For Brivo, Moxa Integration. Part number for access control deployments.

EN-PA-001-X or ENi-PA-001-X

Brivo Eagle Eye Vehicle Surveillance Package (VSP)

VSP subscription required per camera.


Any video subscription (except SD1, as LPR is not supported on analog cameras)

Video subscription is mandatory for any camera connected to Brivo Eagle Eye Video.



Required Bridges/CMVRs:


* Please note: the number of supported cameras changes when LPR is activated. Be sure to reference the latest data sheet and discuss with your sales representative before purchasing.

* Number of additional analytics supported on the same bridge running LPR.


LPR processing is performed on the Brivo Eagle Eye Bridge/CMVR, and Moxa is integrated into the LPR services on the Bridge to ensure the system will function even without an active internet connection. LPR events on the VSP and the database changes will be reflected in the LPR service when the network connection is reestablished. 



Physical Connections


The MOXA unit has six relay outputs, which are used to trigger the gate. They are marked from NO1 to NO6, and their respective common is marked as C next to NO pins. The relay outputs should not be confused with digital outputs. We are only using the relay outputs, marked RX_NO (where X is the output number).


If the gate is connected to R1_NO, then output 1 needs to be configured on the LPR Configuration page in Brivo Eagle Eye Video for the allow list. An example connection for the channel to the barrier and light is provided here. 


For additional wiring details, please refer to the manufacturer’s User Guide.



MOXA I/O Configuration


Very little configuration is required in the I/O module itself, since we send all the parameters (such as which relay, pulse time, etc.) to Moxa from the LPR Application. The license plate list is uploaded to the LPR application (see below for more on LPR configuration). This ensures the integration continues to work seamlessly in offline mode if the internet connection is lost.


For more information, see the MOXA User Manual. The default IP address of the unit is 192.168.127.254. You can also scan the network to find it using the manufacturer's tool, “ioSearch,” available on their website.


If multiple ioLogik E1200 units are installed on the same network, remember that each unit has the same default IP address. You will need to assign a different IP address to each unit to avoid IP conflicts. Also, please ensure the Bridge/CMVR and Moxa are in the same IP range (IP address and subnet).


Moxa network settings:


Configuring LPR Analytics


LPR Analytics are enabled in the Analytics section of Brivo Eagle Eye Video, under Camera Settings. Once enabled, LPR configuration is accessed by clicking to open LPR Settings. Please ensure the LPR Add-on Feature Local ID is enabled as this activates the access control tab in the configuration UI.




Setup notes:

  • Integration Type must be set to External I/O Moxa. 

  • Enter the MOXA IP Address under External I/O IP. 


The next three fields are used to define the relay that needs to be triggered for:

  • Allow list (access granted)

  • Deny list 

  • Unregistered vehicles


If no relay needs to be triggered for the last two options, leave them blank.


The list of license plates (LPs) can be entered manually by clicking the + icon on the screen, or you can upload a .csv file with the LPs. An example .csv can be downloaded to ensure you format the file with the correct headers. After configuring, click the save button to save the configuration and vehicle list.


Camera Installation Considerations


Camera positioning is paramount to a smooth, high-accuracy LPR installation. Once properly installed, implementing and using a License Plate Credential becomes a seamless experience, as the gate/barrier or door opens automatically when authorized vehicles approach. 



Front License Plate Capture


Note: Always keep in mind that the barrier should not block the camera’s field of view, or it could interfere with reading license plates. It is also best practice to place the camera ahead of the gate/barrier, rather than behind it.


Distance A - The distance between the barrier and the LPR imaging area. The distance is best kept from 3–10 feet (~1–3 meters). This is to ensure that the vehicle triggers are sent to the barrier in a timely manner, so it opens as the vehicle approaches, while leaving no additional space to allow unauthorized vehicle access.


Distance B - The distance between the camera and the LPR imaging area. For gate access control, the distance is best kept from 6–12 feet (~2–4 meters). Access control requires high accuracy, which in turn requires clear license plate imaging to enable consistent LPR. A shorter distance allows for better night-time imaging, as the IR power can best illuminate only nearby plates. 

Distance C - The height of the camera installation. For gate access control, it is best to position cameras at 4–8 feet (~1.5–2.5 meters) high. Note that the camera should be angled down by approximately 30 degrees to avoid direct sunlight. 


Rear License Plate Capture


Distance A - The distance between the barrier and the LPR imaging area. The distance is best kept from 15–25 feet (~5–8 meters). This is to ensure that vehicle triggers are sent to the barrier in a timely manner, so it opens as the vehicle approaches, while leaving no space for unauthorized vehicle access. The vehicle imaging area considered here is the rear license plate.


Distance B - The distance between the camera and the LPR imaging area. For gate access control, the distance is best kept from 6–10 feet (~2–4 meters). Access control requires high accuracy, which in turn requires clear license plate imaging to enable consistent LPR. A shorter distance allows for better night-time imaging as the IR power can best illuminate only nearby plates.


Distance C - The height of the camera installation. For gate access control, it is best to position cameras between 4–9 feet (1.5–3 meters) high. The camera should be angled down by approximately 30 degrees to avoid direct sunlight.


Related Application Notes and Collateral